Htek UC926 Quickstart Guide

Htek UC926 Quickstart Guide

Getting Started

LED
Power Indicator: Steady green when power on, blinking green when the call is ringing. Line Keys: Steady green: During the conversation, or plan to dial a call. Blinking red: The call is ringing. Off: Idle interface.

 

Place a call
Three ways to make a call:

  • Handset: Pick up the handset; enter the number, then press the send soft key or press #.
  • Speaker: Press speaker button or the line keys; enter the number, then press the send soft key or press #.
  • Headset: Press the headset button; enter the number, then press the send soft key or press #. 


End a call

To end a call in three different modes:

  • Handset: Hang up the handset or press the cancel soft key.
  • Speaker: Press speaker button, or press the cancel soft key.
  • Headset: Press the cancel soft key. 


Answer a call

  • Handset: Pick up the handset.
  • Speaker: Press speaker button.
  • Headset: Press headset button. 

Note:You can also reject the call by press the Reject soft key.

Redial
Press the redial button to redial the last call that dialed.

Hold
Press the hold button or press the hold soft key during a call to hold the call. Press the hold button or resume soft key to resume the call.

Call Transfer
Blind Transfer

  1. Press the transfer button or transfer soft key during the conversation, the call is on hold now.
  2. Enter the number that transfers to.
  3. Press the transfer button or the transfer soft key and now the blind transfer completed.

If a BLF button is setup for the extension you are wanting to transfer to, pressing the BLF button will automatically perform a Blind Transfer

Attended Transfer (at least one line key set as Auto)

  1. Press the transfer button or transfer soft key during the conversation, the call is on hold now.
  2. Enter the number that transfer to and press the send soft key or #.
  3. Start the second conversation, press the transfer button or transfer soft key, then transfer completed. 

Semi-Attended Transfer (at least one line key set as Auto)

  1. Press the transfer button or transfer soft key during the conversation, the call is on hold now.
  2. Enter the number transfer to, and then press the transfer button, then you can hear the ring tone.
  3. Press the transfer button or the Tran soft key and now the Semi-attended transfer completed. 


Call Conference
Assuming that A and B are in conversation. A wants to bring C in a conference:

  1. A press line 2, the call is placed on hold.
  2. A enter the number of C and then press the conference button send soft key or C answers the call.
  3. A press the conference button or the conference soft key, then A, B and C are now in a conference.


Call Mute
Press the mute key to mute the microphone during the call. Press again to un-mute the conversation.


    • Related Articles

    • Htek Manual Provisioning

      Prerequisites Access to phone web gui If your Htek phone requires the manual input of our provisioning url, please follow the steps listed below.  Instructions Log into webgui of the Htek phone by entering its IP address (192.168.x.x) into a web ...
    • iOS UC Softphone

      Scan the QR code or click here for the App Store Disclaimer Most issues with audio or call quality will be directly related to network issues. Due to the unpredictable nature of mobile and wireless networks, it will be solely up to the user to ...
    • Android UC Softphone

        Scan the QR code or click here for the Android Store Disclaimer Most issues with audio or call quality will be directly related to network issues. Due to the unpredictable nature of mobile and wireless networks, it will be solely up to the user to ...
    • Factory reset process

      Prerequisites Reseller level permissions to clear credentials Access to portal First Step - Clearing Auth Credentials Before factory resetting your device you need to first perform a task in the portal. Please note, if you do not see these options ...
    • Using Poly Studio With UC Connect

      Changing UC Connect To Poly StudioWhen starting a meeting, before joining, click on device settings. If you have already started the meeting and joined, you can reach these settings by clicking the top-right menu button, then, click camera and audio ...